冷再生机时打滑的原因及方法和优点有哪些，接下来广轩工程机械将带大家一起来了解下，希望以下的介绍可以让大家更好的了解铣刨机在运用时会出现的一些问题，希望对大家有所帮助。客户在求租冷再生机使用过程中，不可避免地会出现消耗和磨损，其中，冷再生机输送带特别容易出现问题，运行时间长，可能出现打滑现象，影响工作效率。

What are the reasons, methods, and advantages of slipping when using a cold regeneration machine? Next, Guangxuan Engineering Machinery will take you to understand. We hope that the following introduction can help you better understand some of the problems that may occur when using a milling machine. We hope it will be helpful to you. During the process of using a cold regeneration machine, customers inevitably encounter consumption and wear. Among them, the conveyor belt of the cold regeneration machine is particularly prone to problems, running for a long time, and may experience slipping, affecting work efficiency.

1、初始张力太小。

1. The initial tension is too small.

输送带离开滚筒的张力不够，会引起皮带打滑。一般来说，这种情况是在启动时发生的。如果你想它，你必须调整张力装置和增加初始张力。

Insufficient tension of the conveyor belt leaving the drum can cause the belt to slip. Generally speaking, this situation occurs at startup. If you want to solve it, you must adjust the tension device and increase the initial tension.

2、摩擦力是不够的。

2. Friction is not enough.

传动滚筒与输送带之间的摩擦力不足以引起滑动。造成这种现象的主要原因是输送带上的水或环境潮湿。方法：在气缸中加入一些松香末。注意不要用手而应用鼓风设备吹入，以免发生事故。

The frictional force between the transmission drum and the conveyor belt is insufficient to cause sliding. The main reason for this phenomenon is the water on the conveyor belt or the humid environment. Solution: Add some rosin powder to the cylinder. Be careful not to use your hands and use a blowing device to blow in to avoid accidents.

3、轴承损坏

3. Bearing damage

尾部滚子轴承损坏或不旋转。造成损坏的原因是机器尾部太浮、太沉，不能及时修理和更换损坏的或不灵活的部件，这导致由打滑引起的阻力增加。

Damaged or non rotating tail roller bearings. The cause of damage is that the tail of the machine is too floating or heavy, and damaged or inflexible components cannot be repaired and replaced in a timely manner, which leads to increased resistance caused by slipping.

4、起步太快。

4. Starting too fast.

起动速度太快，不能打滑。这个时候可慢速启动。如果使用鼠笼电机，则可以移动两次，然后被，还可以有效地克服打滑现象。

The starting speed is too fast to slip. At this time, it can be started slowly. If a squirrel cage motor is used, it can be moved twice and then activated, effectively overcoming slipping.

5、输送带负荷过大。

5. The conveyor belt is overloaded.

输送带的负荷过大，超过电机能力也会打滑。打滑的优点是保护电机。否则，电动机将长期燃烧。但对于运行来说则是打滑事故。

The load on the conveyor belt is too high, exceeding the motor's capacity can also cause slippage. The advantage of slipping is to protect the motor. Otherwise, the motor will burn for a long time. But for operation, it is a slip accident.

感谢您的阅读，此文的文章来源：冷再生机租赁更多的内容和问题请点击：https://www.sddhfjx.com们会继续努力的为您提供服务，感谢您的支持！

Thank you for reading. The source of this article is: Cold Recycling Machine Rental. For more information and questions, please click: https://www.sddhfjx.com We will continue to work hard to provide you with services. Thank you for your support!