欢迎访问山东途畅路桥工程有限公司网站!

冷再生机租赁,水泥撒布车出租

施工租赁热线

18264104888

您现在所在的位置 :首页 - 新闻中心 > 行业资讯
行业资讯

水泥撒布车传感器的使用方法!
来源:https://www.sddhfjx.com/ 日期:2020-09-08
  传感器的使用
  Use of sensors
  传感器位于绞龙、计量器及排杂电机位置,主要起到转速信号传感的作用。
  The sensor is located in the position of auger, metering device and trash removal motor, which mainly plays the role of speed signal sensing.
  电感式传感器自带调节丝纹,可调节传感距离;传感器后尾部正常工作时为黄色传感灯闪烁,如正好处于传感齿牙位置时为黄色传感灯常亮,通常离传感齿牙3mm左右。
  The inductive sensor has its own adjustable silk grain, which can adjust the sensing distance; when the rear tail of the sensor works normally, the Yellow sensor light flashes, if it is just in the position of the sensing tooth, the Yellow sensor light is always on, usually about 3 mm away from the sensing tooth.
  1.电感式传感器需要检查以下几点:
  1. Inductive sensor needs to check the following points:
  (1)、传感距离是否过远
  (1) Is the sensing distance too far
               水泥撒布车出租
  (2)、传感位置是否偏离齿轮牙盘
  (2) Whether the sensing position deviates from the gear tooth disc
  (3)、用物品在传感器前端位置移动测试,查看传感灯是否闪烁,如常亮则有可能需要更换传感器
  (3) Use the object to move the front end of the sensor to check whether the sensor lamp flickers. If it is normally on, the sensor may need to be replaced
  2.如确定传感器已损坏,临时可运用参数设置里的调试功能临时施工,同时联系我司及时配发配件,具体步骤如下:
  2. If it is confirmed that the sensor has been damaged, the debugging function in parameter setting can be used for temporary construction, and at the same time, contact our company to distribute accessories in time. The specific steps are as follows:
  (1)、按照以下顺序操作:
  (1) And operate in the following order:
  状态→诊断→输出,调整到输出检测页面
  Status → diagnosis → output, adjust to output detection page
  (2)、旋转右上角旋转调钮选择需要调试的传感器,选择调试功能后设备能暂时正常运转。
  (2) Rotate the upper right corner knob to select the sensor to be debugged. After the debugging function is selected, the equipment can operate normally temporarily.
  3.选择调试功能后使用需要注意:
  3. After the debugging function is selected, attention should be paid to:
  调试后转速会和原转速有所不同,有可能会高于或低于原转速,同时对撒布量的准确控制会产生一定的影响。
  After debugging, the speed will be different from the original speed, which may be higher or lower than the original speed, and it will have a certain impact on the accurate control of spreading amount.
  以上是关于水泥粉料撒布车传感器的使用方法,希望对大家有所帮助,如您还有其他问题欢迎咨询我们的网站。
  The above is about the use of the sensor of cement powder spreader, hope to help you, if you have other questions, please consult our website.
  • 上一条:大部分企业选择冷再生机的理由?
  • 下一条:冷再生技术质量检查程序是什么?
  • 相关产品: